帮忙翻译一下弹簧扳道器说明书

钢轨配件-扳道器 怎样保养？~

作业不到100小时便更换油一次，以后每作业500小时换油一次，要考虑用新油时兼容性问题，要不把油缸彻底清理。等等还是自己看 中翔网吧

bandaoqiyugangguidechicuen

SL-120 type of flexible railway switch
Manual
A summary
1. SL-120 type of flexible railway switch (Abbreviations: railway switch) is a manual switch turnout equipment.
2. To its spring tension to achieve the turnout to be anti-bit conversion, and will be maintained at its anti-bit capability.
3. Easily apply to "squeeze bifurcated fault" circumstances turnout, once crowded bifurcated not damaged equipment.
4. Lock will be on the base axis of penetration and the locking hole with padlock to lock in turnout for anti-bit state to facilitate a bifurcated traffic safety.
The product features
1. Handle length scalable 290 MM, when the turnout conversion little resistance, length can be shortened handle the contrary, the extension handle length.
2. Handle扳动itinerary for the decrease, to handle the rotating 180 degrees to facilitate human operator.
3 above telescopic handle with rotating the casing by spring sales of the two filed, after falling into the adjustment to achieve.
4. To overcome扳动resistance, the controller design for the core head slider structure, its structure扳动flexible.
5. Rectangular Shui rotating spindle center, equipped with roller bearing, raising product life and accuracy.
6. Where rotation axis between holes, are equipped with a self-lubricating properties of materials bush.
7. Rod connected with the turnout, using the fine-tuning, in the use after the installation process, not dismantle its connecting pin, the turnout openings can be posted and the state of adjustment.
Three technical parameters
1. Apply ≤ 120 mm openings Turnout
2. Applicable conversion turnout resistance ≤ 1960 N (200KG)
3. Rod largest linear displacement of 209 mm
4. Installation of the two枕木center distance 650 mm, with the rod tip Department枕木two bifurcated centerline distance of 350 mm
5. Installation of the double-track railway lines in the middle, adjustable handle from the center line on both sides should be ≥ 22.5 mm
Principle and the installation of four structural adjustment (see the installation diagram)
1. Gauge before installation, inspection, the turnout laying parameters枕木placed spacing is consistent with the relevant technical standards.
2. Installed before use撬棍respectively拨动two apical orbit so close affixed to the basic track-inspection bifurcated Tsim and刨切paragraph of whether the stickers, a non-bifurcated sharp gap best,刨切of the gap should not be large at 1 mm.
3. Angle steel structure will be the installation of devices, one end with 22 mm × 145 mm solid wood screw道钉pinch points in turnout traction on both sides of the wooden pillow-head, the other side needs in line, the laying of a wooden pillow, in the same pinch solid wood枕上.
4. Rod side and right-angle Shui, for fine-tuning the other side of the bar association and the turnout connected together.
5. When railway switch device with the turnout has been fixed link integrity, the first to tie the handle perpendicular to the center position, that is a right angle Shui are also at the middle position; began to adjust the fine-tuning the entire rod, the two apical track for turnouts respectively with straight, curly basically the same size opening track. Turnout orifice size should be open for one half, that is, 60 mm.
6. Completed on the basis of the above adjustments, the first pull to handle one end, a sharp track and check whether the basic track of stickers, if space, use fine-tuning device to be corrected if there is still space, adjusting the compression spring nut to increase Spring tension until the secret stickers. Then handle pull to one end, the same method used to adjust the above, also reached the other side of stickers.
7. In the following two circumstances, the handle can be shortened length.
(1) When converting Turnout little resistance when human can扳动
(2) when the turnout in the set, anti-places, for reduced vertical height handle
Whether or shrinkage handle extended its length, method of operation, has filed handle casing on two spring sales and rotating 90 degrees, casing from the connecting rod and handle the role, can hold length adjustment. And then rotated 90 degrees so that the spring-pin inserted into the hole in the handle and restore connectivity role.
8. Handle railway switch to reduce the itinerary to facilitate human operators, to handle the curved shape. So pull from one end to one end, according to the length of the methods of operation telescopic handle, to be rotating 180 degrees for the next扳动facilitated.
9. Structure for the railway switch principle is: rotating through rectangular Shui can be certain angle to the rectangular Shui一臂can handle拨动, and the other arm with a certain tension on the composition of the spring. Tension role in the spring, according to Cartesian Shui not stagnation in the middle of the principle, in tension with a spring rod arm hang, in a Cartesian Shui rotation angle are the two ends have some traction, providing impetus to the conversion Turnout .
Five Maintenance
1. Use of the ministries should be guaranteed complete fasteners, bolts fastening, opening a sales arm angle to prevent loss provisions.
2. Connecting pin in the hole should wear Kuang of not more than 1 mm, excessive Kuang be timely replacement of connecting pin.
3. Should ensure that the turnout conversion process, the ministries movements smooth, rotating flexible, non-card resistance phenomenon.
4. Pin and Hole, the first with the slider handle inter should regularly coated surface oil, and maintain lubrication good.

---

乐安县19714951113： 帮忙翻译一下弹簧扳道器说明书 - ？
止芬克感： SL-120 type of flexible railway switch Manual A summary 1. SL-120 type of flexible railway switch (Abbreviations: railway switch) is a manual switch turnout equipment. 2. To its spring tension to achieve the turnout to be anti-bit conversion, and will be ...

乐安县19714951113： 产品说明书中译英,请高人帮忙翻译一下,谢谢!!!!!! - ？
止芬克感： Equipment operators must be trained to posts to prevent action because of ignorance or negligence caused by equipment failure.Without the permission of the Company of the machine to carry out structural changes and changes in ...

乐安县19714951113： 帮忙分析一下这个问题,为何选B不选AD,最好有详细思路,谢谢! - ？
止芬克感： A、B正确抽去木板瞬间,弹簧的弹力不会变?...

乐安县19714951113： 帮忙翻译一段英语,不要机器翻译,翻译得好有加分~ - ？
止芬克感： 从图32.1可以看出,滚轴适用于轴D,它通过锥齿轮传递扭矩的,增加同样的比率,速度反而会降低.如果增加扭矩,然后通过传送轴G的车轮,从牛顿第三定律,可知,运动...

乐安县19714951113： 请帮忙翻译一下,急？
止芬克感： Discovered that breaks the natural not breakover phenomenon idly. Breaks the natural breakover not to occur idly does not press 0.7~0.8mm when nondefective 1, under nondefective 2 does not press when 0.6mm~0.7mm. When spring ...

乐安县19714951113： 请帮忙翻译一下这段话？
止芬克感： 按照您的要求,我们将在明天出货给您,您是安排到我司新加坡仓库上门提货或是我们送到贵司马来西亚仓库? 另外,请安排以下付款,谢谢! As per your request, we will ship the goods to you tomorrow. Would you like to pick up the goods at ...

乐安县19714951113： 你在做现代文阅读选择题时遇到选项相似的题,你会怎么做() - 上学吧继...？
止芬克感： 鲍勃,约翰,托马斯,院长,保罗,杰克,布鲁克

乐安县19714951113： 高手帮忙翻译一下这些专业英文？
止芬克感： 1.横杆 2.弓形部分=弦 3.塑料罩 4.塑料器皿 5.上部弓形部分 6.(手拧)螺钉 7.焊接螺母 8.高度可调的构造 9.弹簧夹具 10. 室外园艺用吊钩 11.蝶形螺钉 12.应该是stable welded稳定焊接 13.室内标杆

乐安县19714951113： 帮忙翻译一下,急 - ？
止芬克感： Adverse information based on your feedback, your switch terminal settlement of this complaining about bad, we staggered to improve evacuation for handle spring - like your sample because the sample is using ordinary material injection switch ...