懂阀门英语专业术语的进

有懂阀门技术英文用语的来帮帮忙~

这还不容易么 看我的翻译 如果可以你就采纳我的答案噢~~~！！
Titanium Valves: 1. General shall not, without permission Party casting welding repair process. 2. Material forged titanium material shall be ASTM B381 Gr. F2, or Gr. F3. Casting titanium material shall be ASTM B367 Gr. C2, or Gr. C3. Titanium components, the maximum iron content of 0.07% and the maximum hydrogen capacity of 60ppm. Casting the mechanical properties of casting residue to comply with ASTM requirements. Stick Titanium Standard ASTM B348 Gr.5. 3. X-ray detection casting is subject to 100% X-ray detection test, based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. 4. Penetrant testing all the casting in the stress test carried out after the required 100% of the permeability test, in order to avoid casting the cracks, trachoma and so on. 5. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents.  Hastelloy alloy valve 1. Castings Hastelloy Castings Hastelloy C4 and the need to use ASTM A494 Grade CW-2M of the alloy, the largest iron content does not exceed 2%. If you specify the use of Hastelloy C276, Ze Xu using UNS N10276 alloy, mechanical properties required to meet the ASTM minimum requirements. 2. X-ray detection for each casting is subject to ultrasonic or X-ray detection. After each batch and then take 10% of the testing, the nominal diameter greater than or equal 6 "of the body in need of complete testing, greater than or equal 8" in key parts of the body just for testing. -Ray flaw detection test based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. If you have casting did not meet testing standards be admitted to the batch number of the additional testing. If these two happen again does not meet state testing standards, then take all of the batch for testing. 3. Penetrant testing a batch of each supplier is required to provide penetration testing report at the same time need to provide mechanical tests, physical tests and chemical composition of reports. 4. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents.  dual-phase steel valves: 1. A dual-phase steel all of the components required to meet the ASME V111, Div 1, Appendix 7 requirements. 2. Material Duplex steel castings for example, to comply with ASTM A995 Grade 4A for 2205 alloy, grade 6A for the 2507 alloy. Chemical composition, mechanical properties to meet the requirements of subparagraphs 3 to 5. 3. Chemical composition of the amount of corrosion-resistant duplex steel (PREN) according to the formula: PREN = (Cr wt% + 3.3 Mo wt% + 16 N wt%), calculate the value of not less than the following. 2205 Alloy - 34 2507 Alloy - 40 4. Chemical composition requirements are as follows Material 2205 Alloy 2507 Alloy maximum carbon content of 0.030% 0.030% chromium content of 21.5-23% 24-26% nickel content of 4.5-6.5% 5.5-8.0% Mo content of 2.9 -3.5% nitrogen content of 0.145-0.2% 3.6-4.0% 0.24-0.35% maximum sulfur content of 0.02% 0.02% maximum phosphorus content of 0.03% 0.03% maximum silicon content of 1.0% 0.8% maximum manganese content of 2.0% 1.5% tungsten content of 0.5% maximum 0.8% maximum copper content of 0.5% 0.75% 5. mechanical properties requirements are as follows Material 2205 alloy 2507 alloy minimum tensile strength of 620MPa 700MPa 0.2% deformation deflection (minimum) 450 MPa 550MPa Elongation (2in%) 25min 15min maximum stiffness of 290 BHN (30.5 Rc) 310 BFN 6. The remaining test casting heat treatment, the need to use samples of the following tests. Testing methods and the use of the standard details of the Party should be provided. Tension Test    Impact Test hardness testing  corrosion testing 7. Non-destructive testing, after the final heat treatment in accordance with the following annotation can be seen in non-destructive testing penetration testing X-ray detection range of 100% 100% testing a key component of the valve based on ANSI B16 .34 standard ASME VIII Div 1 App 8 ASME VIII Div 1 App 7 processes ASME VIII Div 1 App 8 ASME VIII Div 1 App 7 acceptance ASME VIII Div 1 App 8 ASME VIII Div 1 App 7
可以吧

Shanghai valve Manufacturing Co., Ltd.

泵阀是泵和阀门的统称。 非用于泵的阀门或具有泵作用的阀门。泵和阀常常联系在一起的原因是使用场合。就是说有泵的地方一般都有阀门，有阀门的地方往往需要泵。他们都用于液体输送的地方。当然，阀门还用于气体。真空泵也与气体有关。
另一个联系就是有相当多制造商们既生产泵又生产阀门，其制造材料等也十分相近。
所以一般英文只写阀门。

名片上写的valve pump或者pump valve是为了让人更加了解公司不只做阀还做泵

如果你一定要加的阀可以写成
Shanghai valve&pump Manufacturing Co., Ltd.
写前写后都不影响

以下是阀门行业中公认的一些知名品牌，它们被广泛认可并享有很高的声誉。虽然排名可能因时间和市场情况而有所变化，但以下品牌通常被认为是阀门行业的顶级品牌之一：
水系统阀门和工业阀门以下比较有影响力的一线品牌可以作为参考，但是仅供参考：苏州纽威阀门、上海冠龙阀门、上海奇众阀门、三花、苏盐、神通、苏阀、南方、江一、尧字。
以上厂家只是预估和参考的作用，具体情况可能会因为市场行情的变化、竞争格局大小、产品质量稳定等一系列因素的变化而有所不同或者随时浮动的情况发生。阀门作为工业生产和民用设施中不可或缺的关键装置，其品牌的质量和声誉直接影响着使用者的满意度和信任度。
这些品牌在阀门行业中以其创新技术、高品质产品和可靠性而著名。值得注意的是，市场和行业发展变化快速，不同的排名可能会因时间和地区而有所不同。对于最新的排名信息，建议参考行业报告、专业机构或市场调研数据，以获取更详细和准确的信息。

球阀,阀体材料SCS14A JPI150 ,内件SUS316,全通径,RF法兰，带手柄（生产商标准手柄）；
蝶阀，阀体FCD-S JPI150，蝶板13Cr；
蝶阀，阀体SCS13A JPI150 ，蝶板SCS14A，阀座采用生产商标准材质；
止回阀，阀体SFVC2A JPI800 ，内件13Cr，BC应该是螺栓连接的阀帽（Bolted Cover），升降式，承插焊连接；
针阀，阀体SUSF316L JPI300 ，内件SUS316L，阀座和阀板密封面：司太力合金，螺栓连接的阀帽（Bolted Bonnet）,明杆支架式,承插焊连接，长型阀帽。

球阀SCS14A JPI150边采SUS316全口径射频杠杆制造的性病

蝶阀的FCD - S的JPI150光盘13Cr

蝶阀SCS13A JPI150光盘SCS14A座椅制造的

止回阀SFVC2A JPI800边13Cr BC.LIFT西南

针阀SUSF316L JPI300边材质为SUS316L特殊和差别待遇的STL BB.OS安永西南长长的引擎罩

---

博兴县17689531910： 阀门专业术语英语系列 - ？
房闹接骨： Shanghai valve Manufacturing Co., Ltd.泵阀是泵和阀门的统称. 非用于泵的阀门或具有泵作用的阀门.泵和阀常常联系在一起的原因是使用场合.就是说有泵的地方一般都有阀门,有阀门的地方往往需要泵.他们都用于液体输送的地方.当然,阀门还用于气体.真空泵也与气体有关. 另一个联系就是有相当多制造商们既生产泵又生产阀门,其制造材料等也十分相近. 所以一般英文只写阀门.名片上写的valve pump或者pump valve是为了让人更加了解公司不只做阀还做泵如果你一定要加的阀可以写成 Shanghai valve&pump Manufacturing Co., Ltd. 写前写后都不影响

博兴县17689531910： 懂阀门英语专业术语的进 - ？
房闹接骨： 球阀,阀体材料SCS14A JPI150 ,内件SUS316,全通径,RF法兰,带手柄(生产商标准手柄); 蝶阀,阀体FCD-S JPI150,蝶板13Cr; 蝶阀,阀体SCS13A JPI150 ,蝶板SCS14A,阀座采用生产商标准材质; 止回阀,阀体SFVC2A JPI800 ,内件13Cr,BC应该是螺栓连接的阀帽(Bolted Cover),升降式,承插焊连接; 针阀,阀体SUSF316L JPI300 ,内件SUS316L,阀座和阀板密封面:司太力合金,螺栓连接的阀帽(Bolted Bonnet),明杆支架式,承插焊连接,长型阀帽.

博兴县17689531910： 英译中!请帮忙翻译一下!(比较专业的阀门英语) - ？
房闹接骨： 商标符号 R 前面的可以不翻译 Rite-temp Pressure bala...

博兴县17689531910： 阀门术语中的“阀胆”英文怎么说?谢谢.急急急! - ？
房闹接骨： 阀胆?我专门做阀门技术的,怎么没听说过啊.阀塞:plug阀杆:stem阀盖:bonnet阀体:body

博兴县17689531910： 阀门英语externalpartsbodyandbonnet甚么意思?？
房闹接骨： external parts 指的就是阀门的阀体和阀盖;对应的有阀门的内件trim,比如阀板,阀座,阀杆,填料等 \你所说的Internal parts (Disc- seat)和Trim是1个意思,都是指阀体和阀盖里面所包括的部件

博兴县17689531910： 阀门专业英语？
房闹接骨： Y-GLOBE VALVE: Y型截止阀BW:对焊连接压力:CL1500 = 2MPaPSB:PSB: pressure seal bonnet 压力自密封阀盖OS&Y:outside screw and yoke 螺栓连接阀盖材质:ASTM A216 ,WCB ,SEAT 阀座: A216 WCB+STL,WEDGE:A216 WCB+STL,阀杆STEM:A182 F6 acl.2STL: 是指司太立硬质合金这些东西技术人员一看就懂

博兴县17689531910： 阀门专业里trim这个单词是什么意思? - ？
房闹接骨： 我通常将其翻译为“阀内件”,意思就是2楼所说的“和流体接触的阀门部件”

博兴县17689531910： 销售工程师(主要销售阀门)应该掌握何种专业英语 - ？
房闹接骨： 专业英语就可以了,或者机械上用的英语,要针对专业,专业用语一般是在普通词典上是查询不到的.所以你要买专业方面的书籍看看,或者多看看英文版的阀门基础知识这样就

博兴县17689531910： 求助翻译:阀门专业词汇翻译？
房闹接骨： No. Bore Pressure class Qty Max. torque (Nm) Opening time (S)Type of electric fitting Nominal torque output (Nm) Travel time (S) Max. allowable diameter of stem (mm) Standard of connecting flange (ISO5211) Nominal power (KW) Unit price of electric fitting (RMB) Total price of electric fitting (RMB) Remark

博兴县17689531910： 阀门专业英语!BALL VALVE A216 Gr.WCB/304+PTFE ANSI 150# RF FULL BORE,请问整句意思??？
房闹接骨： 球阀,阀体是WCB A216,球体是304,阀坐PTFE,突面法兰连接,全通径,压力是150LB.这是很普通的美标法兰球阀.