ansys中的如下命令:r,10 real,10 mp,mu,2,0.2 是啥意思 谢谢
finish
/clear
/prep7
et,1,plane42
et,2,solid45
mp,ex,1,2.5e10
mp,nuxy,1,0.2
mp,dens,1,2500
mp,ex,2,2.5e8
mp,nuxy,2,0.4
mp,dens,2,2000
tb,dp,2
tbdata,1,19,32,30
rectng,0,1,0,8
rectng,1,5,0,6
rectng,0,5,0,-16
/pnum,area,1
/pnum,line,1
asel,s,,,2,3,1
aglue,all
numcmp,all
allsel
aplot
lsel,s,,,1,3,2
lesize,all,,,2
lsel,s,,,2,4,2
lesize,all,,,16
amesh,1
lsel,s,,,6,8,2
lesize,all,0.5
lsel,s,,,5
lesize,all,0.5
lsel,s,,,7
lesize,all,0.5
amesh,2
lsel,s,,,11
lesize,all,0.5
lsel,s,,,12
lesize,all,0.5
lsel,s,,,10
lesize,all,0.5
lsel,s,,,9
lesize,all,0.5
amesh,3
extopt,esize,2,0
extopt,aclear,1
type,2
mat,1
vext,1,,,,,-1
extopt,esize,2,0
extopt,aclear,1
mat,2
vext,2,3,1,,,-1
allsel
/view,1,1,1,1
eplot
k,1001,5,6,-5
k,1002,5,0,-5
k,1003,5,-16,-5
l,18,1001
l,1001,1002
l,1002,17
l,1002,1003
l,1003,21
al,22,36,37,38
al,30,38,39,40
vext,19,20,1,-5
vplot
vsel,s,,,4,5,1
vplot
lsel,s,,,36,52,1
lesize,all,0.5
type,2
mat,2
vmesh,all
allsel
vsel,s,,,2,5,1
vplot
eslv,s
nslv,s,1
eplot
nummrg,all
numcmp,all
allsel
/pnum,area,1
/view,1,1,1,1
/ang,1
/pnum,mat,1,2
eplot
allsel
et,3,170
et,4,173
keyopt,4,9,0
keyopt,4,12,2
r,10
real,10
mp,mu,2,0.2
vsel,s,,,1
vplot
asel,s,,,4,6,1
aplot
cm,target,area
type,3
nsla,s,1
esurf,all
esel,s,type,,3
eplot
/psymb,esys,1
allsel
vsel,s,,,2,5,1
vplot
asel,s,,,13
asel,s,,,17
asel,s,,,22
aplot
cm,contact,area
type,4
nsla,s,1
esurf,all
esel,s,type,,4
eplot
/psymb,esys,1
allsel
gplot
save
finish
/solu
asel,s,loc,x,0
aplot
da,all,symm
asel,s,loc,x,5
da,all,all
aplot
asel,s,loc,z,0
da,all,symm
asel,s,loc,z,-5
da,all,all
asel,s,loc,y,-16
da,all,all
allsel
acel,0,9.8,0
nsel,s,loc,y,8
esln,s
eplot
sfe,all,3,pres,,500
antype,static
nlgeom,on
time,1
outres,all,all
allsel
solve
finish
!南京 桩筏计算
!C section
! time 11/24/2002
fini
/cle
long = 12.763 !半承台长度 x方向
ww = 16.925 !半承台宽度 y方向
hh = 0.7 !承台高度
structheight = 7.6 ! 结构高度
pilelen = 40.5
pilediameter = 0.7088
!桩 x 方向发布坐标
*dim,px,array,4,1,1
px(1) = 1.763
px(2) = 3.5 + px(1)
px(3) = 3.45 + px(2)
px(4) = 3.45 + px(3)
!桩 y 方向发布坐标
*dim,py,array,4,1,1
py(1) = 1.725
py(2) = 3.45 + py(1)
py(3) = 3.3 + py(2)
py(4) = 3.3 + px(3)
!最边上5桩坐标
*dim,pxx,array,5,1,1
pyy5 = py(4) + 3.3 ! y 坐标
! x 坐标
pxx(1) = 0
pxx(2) = pxx(1) + 3.113
pxx(3) = pxx(2) + 3.05
pxx(4) = pxx(3) + 3
pxx(5) = pxx(4) + 3
cof = 0.9 !压缩模量转换成弹性模量的系数
! 桩顶为地基平面0标高
soilwidth = ww*1.5
soilnum = 7
*dim,soilthick,array,soilnum,1,1
*dim,soiles,array,soilnum,1,1
soilthick(1) = 0.36 !土层1厚度
soiles(1) = 2e6*cof !土层1模量
soilthick(2) = 0.6 !土层2厚度
soiles(2) = 5.6e6*cof !土层2模量
soilthick(3) = 9.7 !土层3厚度
soiles(3) = 2.9e6*cof !土层3模量
soilthick(4) = 10.2 !土层4厚度
soiles(4) = 2.3e6*cof !土层4模量
soilthick(5) = 3.4 !土层5厚度
soiles(5) = 3.1e6*cof !土层5模量
soilthick(6) = 5.3 !土层6厚度
soiles(6) = 4.3e6*cof !土层6模量
soilthick(7) = 17.8 !土层7厚度
soiles(7) = 8e6*cof !土层7模量
*dim,sbottom,array,soilnum,1,1
sbottom(1) =soilthick(1)
*do,i,2,soilnum
sbottom(i) =sbottom( i-1 ) + soilthick( i )
*enddo
soildeepth= sbottom(7) !计算深度
load1 = 1
load2 = 2
load3 = 3
load4 = 4
! pile and soil's component
!*dim,soilonly,array,soilnum+1,1,1
!*dim,pileonly,array,soilnum+1,1,1
!*do,i,1,soilnum+1
! soilonly(i) = i*10
! pileonly(i) = i*10+2
!*enddo
/prep7
bopt,numb,off
et,1,plane42
ET,2,SOLID45 !185
!* element property
mp,ex,30,2e10 !承台和桩
mp,prxy,30,0.167
mp,dens,30,2.5e3-1e3 ! !kg/m^3 补偿基础
mp,ex,20,1e12 ! water
mp,prxy,20,0.45
mp,dens,20,0.224e3
mp,ex,21,2e10 ! wall
mp,prxy,21,0.167
mp,dens,21,9.795e3
mp,ex,22,2e10 ! pillar
mp,prxy,22,0.167
mp,dens,22,115.8e3
*do,i,1,soilnum
MP,EX,i,soiles( i ) !土层 i
MP,PRXY,i,0.35
*enddo
!创建体
!BLOCK,0,long,0,ww,0,-hh, !承台
rect,0,long,0,ww
!cm,chentai,volu
*do,xx,1,4
*do,yy,1,4
!移动工作平面
!wprota,0,90,0
wpoffs,px( xx ),py( yy ),0
!创建桩
BLC5, 0, 0, pilediameter, pilediameter, 0
! BLC5, 0, 0, pilediameter, pilediameter, pilelen
!恢复工作平面
WPCSYS,-1
*enddo
*enddo
wpoffs,pxx( 1 )+pilediameter/4,pyy5,0
BLC5, 0, 0, pilediameter/2, pilediameter, 0
WPCSYS,-1
*do,xx,2,5
wpoffs,pxx( xx ),pyy5,0
BLC5, 0, 0, pilediameter, pilediameter, 0
WPCSYS,-1
*enddo
!土层
rect,0,long,0,ww !土层1
rect,long,soilwidth,0,ww
rect,0,long,ww,soilwidth
rect,long,soilwidth,ww,soilwidth
aptn,all
aglue,all
! mesh
mshape,1,2d
mshkey,0
smrt,10
lsel,s,loc,y,0
lsel,r,loc,x,0,ww
asll,s,0
asel,r,loc,z,0
cm,soilin,area
amesh,all
alls,all
lsel,s,loc,y,0
asll,s,0
asel,r,loc,z,0
cm,soilonly,area
mshape,0,2d
mshkey,1
alls
cmsel,s,soilin
asel,inve
AESIZE,all,pilediameter
lsel,s,loc,x,long+0.1,soilwidth-0.1
lsel,a,loc,y,ww+0.1,soilwidth-0.1
lesize,all,,,5
amesh,all
alls
!extrude the area to volume
TYPE,2 ! using element type 2, solid 3d element
! soil and pile
*do,i,1,soilnum
asel,s,loc,z,sbottom(i)-soilthick( i )
*if,i,lt,3,then
EXTOPT,ESIZE,1,0, ! size
*else
EXTOPT,ESIZE,3,0, ! size
*endif
MAT,i ! using material type i
*if,i,eq,soilnum,then
vext,all,,,0,0,pilelen - sbottom(soilnum-1)
asel,s,loc,z,pilelen
vext,all,,,0,0,sbottom(soilnum)-pilelen
*else
vext,all,,,0,0,soilthick( i )
*endif
*enddo
alls,all
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,0,sbottom(1)
vsla,s,0
cm,sv1,volu
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,sbottom(1),sbottom(2)
vsla,s,0
cm,sv2,volu
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,sbottom(2),sbottom(3)
vsla,s,0
cm,sv3,volu
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,sbottom(3),sbottom(4)
vsla,s,0
cm,sv4,volu
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,sbottom(4),sbottom(5)
vsla,s,0
cm,sv5,volu
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,sbottom(5),sbottom(6)
vsla,s,0
cm,sv6,volu
asel,s,loc,y,0
asel,a,loc,y,soilwidth
asel,r,loc,z,sbottom(6),pilelen
vsla,s,0
asel,a,loc,y,soilwidth
vsel,a,loc,z,pilelen,sbottom(7)
cm,sv7,volu
cmsel,s,sv1
cmsel,a,sv2
cmsel,a,sv3
cmsel,a,sv4
cmsel,a,sv5
cmsel,a,sv6
cmsel,a,sv7
vsel,inve
cm,piletotal,volu
!load
BLOCK,0,long,0,ww,0,-hh, !底板
wpoffs,0,0,-hh
block,long-0.225,long,0,pyy5,0,-structheight
cm,loadarea1,volu
!rect,0,long-0.225,ww-0.3,ww
!cm,loadarea2,area
block,0,long-0.225,pyy5-0.45,pyy5,0,-structheight
cm,loadarea3,volu
pillarwidth = 0.5
block,px(1)-pillarwidth/2,px(1)+pillarwidth/2,pyy5-11.5-pillarwidth/2,pyy5-11.5+pillarwidth/2,0,-structheight
!blc5,px( 1 ),pyy5-11.5,pillarwidth,pillarwidth
cm,pillarload,volu
block,0,long-0.225,0,pyy5-0.45,0,-structheight
wpcsys,-1
! clear soil 1's mesh
vsel,s,loc,z,0,sbottom(1)
vclear,all
vsel,s,loc,z,-hh-structheight,sbottom(1)
vptn,all
vglue,all
! material property
vsel,s,loc,z,-hh-structheight,-hh
asel,s,loc,y,0
asel,r,loc,z,-hh-structheight,-hh
asel,r,loc,x,0,long-0.225
vsla,s,0
cm,vwater,volu
vatt,20
vsel,s,loc,z,-hh-structheight,0
vsel,r,loc,x,px(1)-pillarwidth/2,px(1)+pillarwidth/2
vsel,r,loc,y,pyy5-11.5-pillarwidth/2,pyy5-11.5+pillarwidth/2
cm,vpillar,volu
vatt,22
vsel,s,loc,z,-hh-structheight,0
cmsel,u,vwater
cmsel,u,vpillar
cm,vwall,volu
vatt,21
alls
! remesh soil 1 by sweeping
mat,1
vsel,s,loc,z,0,sbottom(1)
vsweep,all
! material property
cmsel,s,piletotal
eslv,s
emodif,all,mat,30 ! change pile's material number to 30
alls
! mesh board
mshape,1,3d
mshkey,0
!smat,10
asel,s,loc,z,-hh
AESIZE,all,pillarwidth
vsel,s,loc,z,-hh,0
vmesh,all
mshape,1,3d
mshkey,0
!vsel,s,loc,z,-hh-structheight,-hh
lsel,s,loc,z,-hh-structheight+0.1,-hh-0.1
lesize,all,,,4
asel,s,loc,z,-hh-structheight
lsla,s
lesize,all,pillarwidth
vsel,s,loc,z,-hh-structheight,-hh
vmesh,all
!vsweep,all
alls
!constraint
asel,s,loc,x,0
asel,a,loc,y,0
da,all,symm
asel,s,loc,x,soilwidth
asel,a,loc,y,soilwidth
da,all,symm
asel,s,loc,z,soildeepth
da,all,all,0
alls
! load
acel,,,-9.8
! solve
/solu
alls
solve
real,10：调用实常数10
mp,mu,2,0.2：设置接触单元的摩擦系数，2号材料的摩擦系数为0.2
溥固博健： /prep7 m1=0.009 m2=0.0108 m3=0.012 k1=1.064 k2=7.311 k3=3.378 c1=0.09 c3=0.111 ks=82.3 *dim,disp,array,80,2 !以上为定义参数 et,1,beam3 r,1,2326,3.39e6,115 mp,ex,1,69000 mp,prxy,1,0.3 mp,dens,1,3e-9 !以上为定义单元属性和材料...
江孜县19147185016： ansys 中计算温度时的sf命令命令如下:lsel,s,1,4,1lsel,a,13,16,1nsll,s,1 SF,all,RDSF,0.85, - 1,问:SF命令后0.85sgi代表的什么?后面的 - 1代表什么? - ？
溥固博健：[答案] RDSF (surface-to-surface radiation).面到面的辐射 If Lab = RDSF,VALUE is the emissivity value;0.85是辐射率,the following conditions apply:If VALUE is between 0 and 1,apply a single value to the surface. If Lab = RDSF,VALUE2 is the enclosure ...
江孜县19147185016： ansys命令流vsel,r,174 eslv nsle nsel,r,loc,x,0, - 10 cm,lsjm,node - ？
溥固博健：[答案] vsel是体的选择,其格式:VSEL,Type,Item,Comp,VMIN,VMAX,VINC,KSWP vsel,r,174 是说,在原来选择的基础上“再(r)”选择体174号 eslv是选择此体上附带的单元,nsle是选择单元上附带的节点 nsel,r,loc,x,0,-10 的意思是在原来选择的基...
江孜县19147185016： ansys 网格划分的命令有哪些? - ？
溥固博健： 整理了一些ANSYS常用的命令;但深知自己的水平,还不敢保证完全正确;给大家一些参考,望指正: 1. A,P1,P2,…,P17,P18(以点定义面) 2. AADD,NA1,NA2,…NA8,NA9(面相加) 3. AATT,MAT,REAL,TYPE,ESYS,SECN(指定面的单元...
江孜县19147185016： ansys中命令r和real的区别是什么?？
溥固博健： r是定义实常数时采用的 real是调用实常数
江孜县19147185016： 请问怎么查看ansys中已定义好的实常数特性?下面的命令流里还有两个小问题,谢谢! - ？
溥固博健： 估计这段命令流是用Ansys自己生成的,作者又整理了一下. R命令的格式是R, NSET, R1, R2, R3, R4, R5, R6 其中Nset只是给你当前的实常数集合定个编号而已,而与单元没有什么关系.事实上,对于不同单元,R1到R6能定义的常数的物理意...
江孜县19147185016： ANSYS中有哪些实用的快捷键 - ？
溥固博健： 快捷键: enter——选取或启动 esc——放弃或取消 f1——启动在线帮助窗口 tab——启动浮动图件的属性窗口 pgup——放大窗口显示比例 pgdn——缩小窗口显示比例 end——刷新屏幕 del——删除点取的元件(1个) ctrl+del——删除选取的元...
江孜县19147185016： ansys中 line10是什么意思? - ？
溥固博健： 就是线号为10的直线,10号线 ,ansys建模是通过点,线,面的顺序建模,点就是point1.2.3等,线就用line1.2.3等表示
江孜县19147185016： ansys中link10的结果 - ？
溥固博健： 选择单元中的某个节点的值,比如是位移,然后定义成一个变量,使用显示命令把这个命令显示出来就可以了!NSOL PLVAR 这两个命令需要使用!
江孜县19147185016： ANSYS 里的 asel,s,loc,x,0,a/2 asel,r,loc,y, - d/2,0 这两句话应该怎么解释啊,在线等,急？
溥固博健： 第一个命令通过坐标来选择面的命令 坐标范围是x=0到x=a/2 第二个命令是在选的面里继续选择通过坐标选面 y=-d/2到y=0 最后的效果就是 选择了x=0到a/2 y=-d/2到0 之间的面
